DonnyFL
DonnyFL | YOKOZUNA Moderator
$190.00
$200.00
FEATURES:• Indexed locking system for consistent position and no point of impact changes.• Quick detachment for easy storage and reattachment for shooting.• Comes with a 1/2 x 20 female (barrel/shroud) thread adapter.• Modular design for length adjustment.• Crafted from 6061 T6 aluminum (individual sections) and 7075 aluminum (main QD housing andadapter).
•YOKOZUNA: has the same outer diameter as our Sumo 40.46mm or 1.6
Note: We recommend ordering 1 caliber size up to eliminate the chance of pellet clippingDISCLAIMER: The products on DonnyFL are INTENDED for the use on airguns only. It is a violation of Federal law to use this product in a manner inconsistent for which it was intended for. It is your Responsibility to know the laws in your country, state, county and city and to fully comply with them.
DonnyFL
DonnyFL | RYU Moderator
$175.74
$184.99
FEATURES:• Indexed locking system for consistent position and no point of impact changes.• Quick detachment for easy storage and reattachment for shooting.• Comes with a 1/2 x 20 female (barrel/shroud) thread adapter.• Modular design for length adjustment.• Crafted from 6061 T6 aluminum (individual sections) and 7075 aluminum (main QD housing andadapter).• Quick disconnect rear available for the following moderators.(EMPEROR,SUMO,RONIN,SHOGUN,FX,TANTO,TATSU,KOI,FATBOY)
The RYU has the same diameter as our KOI at 30.48mm or 1.2 inches.
Note: We recommend ordering 1 caliber size up to eliminate the chance of pellet clippingDISCLAIMER: The products on DonnyFL are INTENDED for the use on airguns only. It is a violation of Federal law to use this product in a manner inconsistent for which it was intended for. It is your Responsibility to know the laws in your country, state, county and city and to fully comply with them.
DonnyFL
DonnyFL | EMPEROR V3 Moderator
$227.99
$239.99
This Emperor is for the serious high powered airgunner. This version has a mono-core design and allows you to screw on an optional 6.5 inch extender to make it even quieter.
Features:
compatible with .22, .25, .30, .308, .457 and .50 caliber
Please note: does not come with adapter, please look in our adapter section for the specific adapter for your air rifle.
Endcaps for 1/2 x 20 UNF, M18x1 (big bore), M20x1 (FX Impact/Wildcat)
Precision CNC'd
Comes pre-wrapped in felt and stainless steel mesh
Machined grooves on the outside for easy handling.
Made with 6061 Aluminum, will not work for firearms. Please read disclaimer.
*Note: If you see white lines on the inside of the front cap, that's ok. Those were caused by the prongs holding the pieces while anodizing. They are not pellet clippings.
Note: We recommend ordering 1 caliber size up to eliminate the chance of pellet clippingDISCLAIMER: The products on DonnyFL are INTENDED for the use on airguns only. It is a violation of Federal law to use this product in a manner inconsistent for which it was intended for. It is your Responsibility to know the laws in your country, state, county and city and to fully comply with them.
![DonnyFL | RONIN .357/.457/.50 [BIG BORE] Moderator](http://www.thepelletshop.com/cdn/shop/products/111_f833b5cc-ea70-48e5-bcfa-df3cfeb9484c_1280x.jpg?v=1595468752)
DonnyFL
DonnyFL | RONIN .357/.457/.50 [BIG BORE] Moderator
$175.74
$184.99
Ronin for the .357 is a redesign of the Ronin 1/2 x 20. If you do not like the length of the Emperor, this is an awesome alternative. Rear cap was also changed to reduce weight.
2 x 6.25 inches
Available for .357/.457/.50 caliber airguns
M18x1 threaded end cap
Mono-core design to increase accuracy and limit the chances of pellet clipping
No moving parts or epoxy that may become loose after 1000's of rounds
Precision CNC'd by professional machinist
Sand blasted and anodized for maximum durability
Take apart in less than 10 seconds by unscrewing the rear end cap and pushing back the mono-core. No silly hex key or torch needed when you want to perform maintenance inside the unit.
Comes pre-wrapped in felt
Machined grooves on the outside for easy handling.
Weight 9.7 oz
*Note: If you see white lines on the inside of the front cap, that's ok. Those were caused by the prongs holding the pieces while anodizing. They are not pellet clippings.
DISCLAIMER: The products on DonnyFL are INTENDED for the use on airguns only. It is a violation of Federal law to use this product in a manner inconsistent for which it was intended for. It is your Responsibility to know the laws in your country, state, county and city and to fully comply with them.
DonnyFL
AEA | HP & SF Series | Moderator Adapter #A77
$37.99
$39.99
Adapters are threaded for attaching a moderator
Thread: 1/2 x 20 UNF
Works on AEA HP/SF models & HP SS MAX .30 CAL ONLY
Features:
6061 Aluminum
1/2 x 20 male threads
Black Anodized
DonnyFL
DonnyFL | RONIN Moderator
$175.74
$184.99
Ronin is big and bold, but it looks great even on compact bullpups. "Maybe a little overkill for the .177 and .22 but it looks so damn awesome!" - Donny
Available in .25/.30 and .357 (Big Bore) calibers
2 x 6.5 inches
1/2 x 20 UNF, FX(20mm) & Vulcan thread by request.
Mono-core design to increase accuracy and limit the chances of pellet clipping
No moving parts or epoxy that may become lose after 1000's of rounds
Precision CNC'd by professional machinist
Sand blasted and anodized for maximum durability
Take apart in less than 10 seconds by unscrewing the rear end cap and pushing back the mono-core. No silly hex key or torch needed when you want to perform maintenance inside the unit.
Customizable, you can further dampen the sound by wrapping the interior tube with different sound absorbing materials.
Comes pre-wrapped in felt
Machined grooves on the outside for easy handling.
*Note: If you see white lines on the inside of the front cap, that's ok. Those were caused by the prongs holding the pieces while anodizing. They are not pellet clippings.
Note: We recommend ordering 1 caliber size up to eliminate the chance of pellet clippingDISCLAIMER: The products on DonnyFL are INTENDED for the use on airguns only. It is a violation of Federal law to use this product in a manner inconsistent for which it was intended for. It is your Responsibility to know the laws in your country, state, county and city and to fully comply with them.
DonnyFL
DonnyFL | SUMO Moderator
$142.49
$149.99
One of the original and most popular moderators made by DonnyFL. Great balance between size and sound suppression !
1.6 x 6.5 inches
Mono-core design to increase accuracy and limit the chances of pellet clipping
No moving parts or epoxy that may become lose after 1000's of rounds
Precision CNC'd by professional machinist
Sand blasted and anodized for maximum durability
Take apart in less than 10 seconds by unscrewing the rear end cap and pushing back the mono-core. No silly hex key or torch needed when you want to perform maintenance inside the unit.
Customizable, you can further dampen the sound by wrapping the interior tube with different sound absorbing materials.
Comes pre-wrapped in felt
Machined grooves on the outside for easy handling.
*Note: If you see white lines on the inside of the front cap, that's ok. Those were caused by the prongs holding the pieces while anodizing. They are not pellet clippings.
Note: We recommend ordering 1 caliber size up to eliminate the chance of pellet clippingDISCLAIMER: The products on DonnyFL are INTENDED for the use on airguns only. It is a violation of Federal law to use this product in a manner inconsistent for which it was intended for. It is your Responsibility to know the laws in your country, state, county and city and to fully comply with them.
DonnyFL
DonnyFL | TANTO Moderator
$94.99
$99.99
Features:
1.22 x 5 inches
Available in .22/.25 and .30
Mono-core design
Precision CNC’ed by professional machinist
Sand blasted and anodized for maximum durability
Swappable rear end caps for 1/2 x 20 Bolt, FX (M20x1) Bolt or 1/2 x 20 Cone
Comes pre-wrapped in felt
Machined grooves on the outside for easy handling
Tanto with cone endcap is 5.37 inches
Weight:
1. With 1/2 x 20 Bolt rear end cap: 3.9 oz2. With 1/2 x 20 Cone rear end cap: 4.1 oz3. With M20x1 Bolt rear end cap: 3.5 oz*Note: If you see white lines on the inside of the front cap, that's ok. Those were caused by the prongs holding the pieces while anodizing. They are not pellet clippings.Note: We recommend ordering 1 caliber size up to eliminate the chance of pellet clippingDISCLAIMER: The products on DonnyFL are INTENDED for the use on airguns only. It is a violation of Federal law to use this product in a manner inconsistent for which it was intended for. It is your Responsibility to know the laws in your country, state, county and city and to fully comply with them.
DonnyFL
AEA | HP SS Max .357 Cal | Challenger "BIG BORE" .357/.45/.50 Cal #A91 Moderator Adapters
$37.99
$39.99
This adapter is compatible with the .35/.45/50 Cal AEA Challenger "BIG BORE" (side lever model only) as well as the .357 AEA HP SS Max. #A91
*The HP SS MAX 45/50 does not need an adapter*
Features:
M18x1 male threads
6061 T6 Aluminum
Anodized
Knurled thread protector
DonnyFL
AEA | Challenger Pro Moderator Adapter #A99
$33.24
$34.99
Adapters are threaded for attaching a moderator
Thread: 1/2 x 20 UNF
This adapter converts the factory barrel threads from M14x1 to 1/2 x 20. It is also designed to center the barrel within the shroud.
Features:
6061 T6 Aluminum
Not anodized
Compatible up to .30 caliber
DonnyFL
DonnyFL | EMPEROR V3/RONIN 6.26 EXTENDER
$56.99
$59.99
Is the 10.5 inch Emperor v3 still too loud for you? If so add this 6.25 inch expansion chamber to the rear of the Emperor to make it even quieter. This increases the air volume that gets captured inside the suppressor. Works with the latest version of the Ronin as well. If it has the grooves in the front cap, it's the latest model.
*Note: If you see white lines on the inside of the front cap, that's ok. Those were caused by the prongs holding the pieces while anodizing. They are not pellet clippings.
DISCLAIMER: The products on DonnyFL are INTENDED for the use on airguns only. It is a violation of Federal law to use this product in a manner inconsistent for which it was intended for. It is your Responsibility to know the laws in your country, state, county and city and to fully comply with them.
DonnyFL
DonnyFL | FATBOY 2.0 Moderator
$166.25
$175.00
Features:
Compatible with .177 to .30 calibers
Includes 3 interchangeable air strippers
Redesigned 1/2 x 20 rear cap for easy gripping
Can be used with our 6.25 inch extender for more hush power
Measure 4.25 inches long by 2 inches in diameter
Weighs only 6.7 oz
DonnyFL
DonnyFL | TATSU Moderator
$123.49
$129.99
Tatsu or "Dragon" will be a great addition for shooters who need to take the bark out of their gun yet keep the overall length short. This is a smaller version of the popular Sumo. Features:
1.6 x 4.25
Available in .22/.25 and .30
Mono-core design to increase accuracy and limit the chances of pellet clipping
No moving parts or epoxy that may become loose after 1000's of rounds
Precision CNC'd by professional machinist
Sand blasted and anodized for maximum durability
Take apart in less than 10 seconds by unscrewing the rear end cap and pushing back the mono-core. No silly hex key or torch needed when you want to perform maintenance inside the unit.
Customizable, you can further dampen the sound by wrapping the interior tube with different sound absorbing materials.
Comes pre-wrapped in felt
Machined grooves on the outside for easy handling.
Weight 4.1 oz
*Note: If you see white lines on the inside of the front cap, that's ok. Those were caused by the prongs holding the pieces while anodizing. They are not pellet clippings.Note: We recommend ordering 1 caliber size up to eliminate the chance of pellet clippingDISCLAIMER: The products on DonnyFL are INTENDED for the use on airguns only. It is a violation of Federal law to use this product in a manner inconsistent for which it was intended for. It is your Responsibility to know the laws in your country, state, county and city and to fully comply with them.
DonnyFL
DonnyFL | GREAT KAMI Moderator
$270.74
$284.99
When we first released the Emperor, we never thought there would be a demand for something longer. But now with the .72 cal Zeus on the market, the Great Kami is born.
The baffles are thicker compared to the Emperor to withstand the constant powerful air blast, yet it only weighs 2 more ounces than the Emperor.
Features:
6061 T6 Aluminum
Black anodized
Weighs 1.2 lbs
.72 cal is threaded M23x1 specific for the AEA Zeus .72 CAL
.72 cal threaded with M18x1 is specific for AEA Element Max .58 cal
.45/50 is threaded M18x1
The Zeus .58 cal needs a Great Kami Insert with the .72 cal M23x1 thread. For this insert, please reach out to us directly.
DISCLAIMER: The products on DonnyFL are INTENDED for the use on airguns only. It is a violation of Federal law to use this product in a manner inconsistent for which it was intended for. It is your Responsibility to know the laws in your country, state, county and city and to fully comply with them.
DonnyFL
Air Venturi Avenger Extender/Umarex Origin 1/2 x 20 Adapter #A70
$42.74
$44.99
Adapters are threaded for attaching a moderator
Thread: 1/2 x 20 UNF**DOES NOT FIT ANY OF THE AVENGER X SERIES GUNS**
This version allows you to use a larger suppressor than the Tanto or KOI without having to remove it to fill the gun. Also redesigned to slide over the barrel to keep the barrel centered with the adapter. This reduces the chance of pellet clipping and improves accuracy.
Features:
Compatible with .177 caliber to .25
6061 Aluminum T6
Black anodized
1/2 x 20 male threads
*Make sure to use a suppressor one caliber size up. Works really well and reduces the chance of pellet clipping.