Moderators

DonnyFL DonnyFL | YOKOZUNA Moderator $200.00

FEATURES:• Indexed locking system for consistent position and no point of impact changes.• Quick detachment for easy storage and reattachment for shooting.• Comes with a 1/2 x 20 female (barrel/shroud) thread adapter.• Modular design for length adjustment.• Crafted from 6061 T6 aluminum (individual sections) and 7075 aluminum (main QD housing andadapter). •YOKOZUNA: has the same outer diameter as our Sumo 40.46mm or 1.6 Note: We recommend ordering 1 caliber size up to eliminate the chance of pellet clippingDISCLAIMER: The products on DonnyFL are INTENDED for the use on airguns only. It is a violation of Federal law to use this product in a manner inconsistent for which it was intended for. It is your Responsibility to know the laws in your country, state, county and city and to fully comply with them.

DonnyFL DonnyFL | RYU Moderator $184.99

FEATURES:• Indexed locking system for consistent position and no point of impact changes.• Quick detachment for easy storage and reattachment for shooting.• Comes with a 1/2 x 20 female (barrel/shroud) thread adapter.• Modular design for length adjustment.• Crafted from 6061 T6 aluminum (individual sections) and 7075 aluminum (main QD housing andadapter).• Quick disconnect rear available for the following moderators.(EMPEROR,SUMO,RONIN,SHOGUN,FX,TANTO,TATSU,KOI,FATBOY) The RYU has the same diameter as our KOI at 30.48mm or 1.2 inches. Note: We recommend ordering 1 caliber size up to eliminate the chance of pellet clippingDISCLAIMER: The products on DonnyFL are INTENDED for the use on airguns only. It is a violation of Federal law to use this product in a manner inconsistent for which it was intended for. It is your Responsibility to know the laws in your country, state, county and city and to fully comply with them.

DonnyFL DonnyFL | FATBOY 2.0 Moderator $175.00

Features: Compatible with .177 to .30 calibers Includes 3 interchangeable air strippers Redesigned 1/2 x 20 rear cap for easy gripping Can be used with our 6.25 inch extender for more hush power Measure 4.25 inches long by 2 inches in diameter Weighs only 6.7 oz

DonnyFL | FATBOY 2.0 Extension/Extender Tube

DonnyFL DonnyFL | FATBOY 2.0 Extension/Extender Tube $39.99

Need to make the fat boy quieter? You can add this 3 inch extender to capture more air and reduce the muzzle blast some more. Features: 6061 T6 Aluminum Black anodize Matching outer tube design to the fat boy Also compatible with the Ronin and Emperor

DonnyFL DonnyFL | FATBOY 2.0 Muzzle Brake $29.99

This muzzle brake or air stripper screws onto the front of the fat boy. Note: This unit does not come with the individual air strippers. You can change the caliber size by using the inserts that was included with the fat boy. Features: Made of aluminum 6061 T6 Black anodize Weights 2.9 oz Add the optional 3 inch extender for the Fatboy to make it quieter!EXTENDER!

DonnyFL DonnyFL | GREAT KAMI Moderator $284.99

When we first released the Emperor, we never thought there would be a demand for something longer. But now with the .72 cal Zeus on the market, the Great Kami is born. The baffles are thicker compared to the Emperor to withstand the constant powerful air blast, yet it only weighs 2 more ounces than the Emperor. Features: 6061 T6 Aluminum Black anodized Weighs 1.2 lbs .72 cal is threaded M23x1 specific for the AEA Zeus .72 CAL .72 cal threaded with M18x1 is specific for AEA Element Max .58 cal .45/50 is threaded M18x1 The Zeus .58 cal needs a Great Kami Insert with the .72 cal M23x1 thread. For this insert, please reach out to us directly. DISCLAIMER: The products on DonnyFL are INTENDED for the use on airguns only. It is a violation of Federal law to use this product in a manner inconsistent for which it was intended for. It is your Responsibility to know the laws in your country, state, county and city and to fully comply with them.

DonnyFL | EMPEROR V3/RONIN 6.26 EXTENDER

DonnyFL DonnyFL | EMPEROR V3/RONIN 6.26 EXTENDER $59.99

Is the 10.5 inch Emperor v3 still too loud for you? If so add this 6.25 inch expansion chamber to the rear of the Emperor to make it even quieter. This increases the air volume that gets captured inside the suppressor. Works with the latest version of the Ronin as well. If it has the grooves in the front cap, it's the latest model. *Note: If you see white lines on the inside of the front cap, that's ok. Those were caused by the prongs holding the pieces while anodizing. They are not pellet clippings. DISCLAIMER: The products on DonnyFL are INTENDED for the use on airguns only. It is a violation of Federal law to use this product in a manner inconsistent for which it was intended for. It is your Responsibility to know the laws in your country, state, county and city and to fully comply with them.

DonnyFL DonnyFL | EMPEROR V3 Moderator $239.99

This Emperor is for the serious high powered airgunner. This version has a mono-core design and allows you to screw on an optional 6.5 inch extender to make it even quieter. Features: compatible with .22, .25, .30, .308, .457 and .50 caliber Please note: does not come with adapter, please look in our adapter section for the specific adapter for your air rifle. Endcaps for 1/2 x 20 UNF, M18x1 (big bore), M20x1 (FX Impact/Wildcat) Precision CNC'd Comes pre-wrapped in felt and stainless steel mesh Machined grooves on the outside for easy handling. Made with 6061 Aluminum, will not work for firearms. Please read disclaimer. *Note: If you see white lines on the inside of the front cap, that's ok. Those were caused by the prongs holding the pieces while anodizing. They are not pellet clippings. Note: We recommend ordering 1 caliber size up to eliminate the chance of pellet clippingDISCLAIMER: The products on DonnyFL are INTENDED for the use on airguns only. It is a violation of Federal law to use this product in a manner inconsistent for which it was intended for. It is your Responsibility to know the laws in your country, state, county and city and to fully comply with them.

DonnyFL DonnyFL | RONIN .357/.457/.50 [BIG BORE] Moderator $184.99

Ronin for the .357 is a redesign of the Ronin 1/2 x 20. If you do not like the length of the Emperor, this is an awesome alternative. Rear cap was also changed to reduce weight. 2 x 6.25 inches Available for .357/.457/.50 caliber airguns M18x1 threaded end cap Mono-core design to increase accuracy and limit the chances of pellet clipping No moving parts or epoxy that may become loose after 1000's of rounds Precision CNC'd by professional machinist Sand blasted and anodized for maximum durability Take apart in less than 10 seconds by unscrewing the rear end cap and pushing back the mono-core. No silly hex key or torch needed when you want to perform maintenance inside the unit. Comes pre-wrapped in felt Machined grooves on the outside for easy handling. Weight 9.7 oz *Note: If you see white lines on the inside of the front cap, that's ok. Those were caused by the prongs holding the pieces while anodizing. They are not pellet clippings. DISCLAIMER: The products on DonnyFL are INTENDED for the use on airguns only. It is a violation of Federal law to use this product in a manner inconsistent for which it was intended for. It is your Responsibility to know the laws in your country, state, county and city and to fully comply with them.

DonnyFL DonnyFL | RONIN Moderator $184.99

Ronin is big and bold, but it looks great even on compact bullpups. "Maybe a little overkill for the .177 and .22 but it looks so damn awesome!" - Donny Available in .25/.30 and .357 (Big Bore) calibers 2 x 6.5 inches 1/2 x 20 UNF, FX(20mm) & Vulcan thread by request. Mono-core design to increase accuracy and limit the chances of pellet clipping No moving parts or epoxy that may become lose after 1000's of rounds Precision CNC'd by professional machinist Sand blasted and anodized for maximum durability Take apart in less than 10 seconds by unscrewing the rear end cap and pushing back the mono-core. No silly hex key or torch needed when you want to perform maintenance inside the unit. Customizable, you can further dampen the sound by wrapping the interior tube with different sound absorbing materials. Comes pre-wrapped in felt Machined grooves on the outside for easy handling. *Note: If you see white lines on the inside of the front cap, that's ok. Those were caused by the prongs holding the pieces while anodizing. They are not pellet clippings. Note: We recommend ordering 1 caliber size up to eliminate the chance of pellet clippingDISCLAIMER: The products on DonnyFL are INTENDED for the use on airguns only. It is a violation of Federal law to use this product in a manner inconsistent for which it was intended for. It is your Responsibility to know the laws in your country, state, county and city and to fully comply with them.

DonnyFL DonnyFL | SHOGUN Moderator $184.99

If you thought Sumo was quiet wait until you hear Shogun. Shogun is just like Sumo but 1.5 inches longer. Donny added an additional 1 inch chamber as well as increase the first expansion chamber by .5 inches and the chamber by the exit hole another .5 inches. This design is very effective. 1.6 x 8 inches Available in .25 and .30 calibers Available in 1/2x20 UNF, FX(20mm) & Vulcan Thread by request. Mono-core design to increase accuracy and limit the chances of pellet clipping No moving parts or epoxy that may become lose after 1000's of rounds Precision CNC'd by professional machinist Sand blasted and anodized for maximum durability Take apart in less than 10 seconds by unscrewing the rear end cap and pushing back the mono-core. No silly hex key or torch needed when you want to perform maintenance inside the unit. Customizable, you can further dampen the sound by wrapping the interior tube with different sound absorbing materials. Comes pre-wrapped in felt Machined grooves on the outside for easy handling. *Note: If you see white lines on the inside of the front cap, that's ok. Those were caused by the prongs holding the pieces while anodizing. They are not pellet clippings. Note: We recommend ordering 1 caliber size up to eliminate the chance of pellet clippingDISCLAIMER: The products on DonnyFL are INTENDED for the use on airguns only. It is a violation of Federal law to use this product in a manner inconsistent for which it was intended for. It is your Responsibility to know the laws in your country, state, county and city and to fully comply with them.

DonnyFL DonnyFL | SUMO Moderator $149.99

One of the original and most popular moderators made by DonnyFL. Great balance between size and sound suppression ! 1.6 x 6.5 inches Mono-core design to increase accuracy and limit the chances of pellet clipping No moving parts or epoxy that may become lose after 1000's of rounds Precision CNC'd by professional machinist Sand blasted and anodized for maximum durability Take apart in less than 10 seconds by unscrewing the rear end cap and pushing back the mono-core. No silly hex key or torch needed when you want to perform maintenance inside the unit. Customizable, you can further dampen the sound by wrapping the interior tube with different sound absorbing materials. Comes pre-wrapped in felt Machined grooves on the outside for easy handling. *Note: If you see white lines on the inside of the front cap, that's ok. Those were caused by the prongs holding the pieces while anodizing. They are not pellet clippings. Note: We recommend ordering 1 caliber size up to eliminate the chance of pellet clippingDISCLAIMER: The products on DonnyFL are INTENDED for the use on airguns only. It is a violation of Federal law to use this product in a manner inconsistent for which it was intended for. It is your Responsibility to know the laws in your country, state, county and city and to fully comply with them.

DonnyFL DonnyFL | KOI Moderator $144.99

With a new rugged front cap design, signature DonnyFL body grooves and bolt endcap, the KOI is a great addition to any shrouded or un-shrouded air rifle. This model has the smallest outer diameter compared to the other DonnyFL models but don’t let the size fool you. With the added vent holes around the front, it is as impressive as the others. Features: Available in .22/.25 and .30 Mono-core design Precision CNC’ed by professional machinist Sand blasted and anodized for maximum durability Swappable rear end caps for 1/2 x 20 Bolt, FX (M20x1) Bolt or 1/2 x 20 Cone Comes pre-wrapped in felt Machined grooves on the outside for easy handling Weight: 1. With 1/2 x 20 Bolt rear end cap: 4.7 oz2. With 1/2 x 20 Cone rear end cap: 5.0 oz3. With M20x1 Bolt rear end cap: 4.6 oz4. With M14x1.25 Bolt rear end cap: 4.6 oz*Note: If you see white lines on the inside of the front cap, that's ok. Those were caused by the prongs holding the pieces while anodizing. They are not pellet clippings. Note: We recommend ordering 1 caliber size up to eliminate the chance of pellet clippingDISCLAIMER: The products on DonnyFL are INTENDED for the use on airguns only. It is a violation of Federal law to use this product in a manner inconsistent for which it was intended for. It is your Responsibility to know the laws in your country, state, county and city and to fully comply with them.

DonnyFL DonnyFL | TATSU Moderator $129.99

Tatsu or "Dragon" will be a great addition for shooters who need to take the bark out of their gun yet keep the overall length short. This is a smaller version of the popular Sumo. Features: 1.6 x 4.25 Available in .22/.25 and .30 Mono-core design to increase accuracy and limit the chances of pellet clipping No moving parts or epoxy that may become loose after 1000's of rounds Precision CNC'd by professional machinist Sand blasted and anodized for maximum durability Take apart in less than 10 seconds by unscrewing the rear end cap and pushing back the mono-core. No silly hex key or torch needed when you want to perform maintenance inside the unit. Customizable, you can further dampen the sound by wrapping the interior tube with different sound absorbing materials. Comes pre-wrapped in felt Machined grooves on the outside for easy handling. Weight 4.1 oz *Note: If you see white lines on the inside of the front cap, that's ok. Those were caused by the prongs holding the pieces while anodizing. They are not pellet clippings.Note: We recommend ordering 1 caliber size up to eliminate the chance of pellet clippingDISCLAIMER: The products on DonnyFL are INTENDED for the use on airguns only. It is a violation of Federal law to use this product in a manner inconsistent for which it was intended for. It is your Responsibility to know the laws in your country, state, county and city and to fully comply with them.

DonnyFL FX/DonnyFL Moderator $119.99

This is a custom size that comes with your FX guns if you decide to upgrade the suppressor. Same length as the Tanto but larger in diameter. The outer diameter is comparable to the FX factory suppressor. Features: 1.36 x 5 inches Available in .25 & 30 Note: We recommend ordering 1 caliber size up to eliminate the chance of pellet clippingDISCLAIMER: The products on DonnyFL are INTENDED for the use on airguns only. It is a violation of Federal law to use this product in a manner inconsistent for which it was intended for. It is your Responsibility to know the laws in your country, state, county and city and to fully comply with them. We don't recommend using this with the FX Panthera or FX Panthera Hunter.

Find anything you need

Fast Shipping

Quality Control

Mounting & Sighting