DonnyFL
DonnyFL | Yokozuna Spare Baffles
$30.00
Customize the size of your Yokozuna or replace sections of your unit with these individual parts. Please note I would not add more than 2 extra baffles on top of the factory units. If you plan to do so, I would recommend going one caliber size up.
*The products on DonnyFL are INTENDED for use on airguns only. It is a violation of Federal law to use this product in a manner inconsistent with what it was intended for.
DonnyFL
DonnyFL | Yokozuna Spare Extender
$30.00
Customize the size of your Yokozuna or replace sections of your unit with these individual parts. Please note I would not add more than 2 extra baffles on top of the factory units. If you plan to do so, I would recommend going one caliber size up.
*The products on DonnyFL are INTENDED for use on airguns only. It is a violation of Federal law to use this product in a manner inconsistent with what it was intended for.
DonnyFL
EDGun | M14x1.25 To 1/2 x 20 Barrel Adapter A98
from $23.00
Adapters are threaded for attaching a moderator
Thread: M14x1.25 to 1/2 x 20 UNF
This adapter is about 22mm OD x 38.30mm Length. It converts barrel threads from M14x1.25 to 1/2 x 20.
Works on EDgun Leshiy 2 (use with aluminum handguard to mount on bigger moderators)
Silver Does not come with a thread protector.
Features:
6061 T6 Aluminum
Silver (no anodize)
DonnyFL
Epoch Moderator Adapter #A112
$39.99
Product description
If you decide not to use the factory Skout moderator, use this adapter to allow you to screw on a different moderator with M18X1 threads.
Features:
6061 Aluminum
Black anodize
Knurled thread protector
Made for the .357 caliber Skout
DonnyFL
Extended Quick Disconnect 1/8 BSP #M20
$19.99
This extended quick disconnect (QD) makes it easy for those guns with hard to reach fill nipples. A must have for FX Impacts.
1/8 BSP male threads
Max 5000 psi (Do not exceed recommended pressure)
Release collar close to 1.20 inches long
Comes with sealed washer
DonnyFL
FX Wildcat Mag Holder M27
$25.00
With Matt247365 from Airgun Nation's blessing, I am happy to offer these easy to install Wildcat mag holders. Compatible with .177 .22 .25 and .30 caliber. Your magazine clicks securely into the Mag holder using it’s own ball bearing and can rotate for easy loading with one hand while on the gun. As many as 4 Magholders can fit on the Wildcat at one time. You can mount 1, 2, 3 or 4 in a variety of configurations facing either to the front or to the rear and on either side or on both sides.
Features:
Made of 6061 T6 aluminum
black anodize
CNC machined
Uses 2.5 mm Hex key
DonnyFL
FX/DonnyFL Moderator
$119.99
This is a custom size that comes with your FX guns if you decide to upgrade the suppressor. Same length as the Tanto but larger in diameter. The outer diameter is comparable to the FX factory suppressor.
Features:
1.36 x 5 inches
Available in .25 & 30
Note: We recommend ordering 1 caliber size up to eliminate the chance of pellet clippingDISCLAIMER: The products on DonnyFL are INTENDED for the use on airguns only. It is a violation of Federal law to use this product in a manner inconsistent for which it was intended for. It is your Responsibility to know the laws in your country, state, county and city and to fully comply with them.
We don't recommend using this with the FX Panthera or FX Panthera Hunter.
DonnyFL
Hatsan Blitz M18 X 1 Adapter A117
$39.99
This adapter allows you to screw on an airgun suppressor with M18x1 threads.
***New Improved For More Air Flow.***
I recommend going with the Ronin with this gun. I have it installed on my personal gun and it works flawlessly. However, results may vary and might need modification to work in semi auto mode. This gun is similar to the Bullmaster and others have been able to fix the issue by replacing the spring. Go to your hardware store and look for a lighter spring. I got mine from Ace hardware and it fixed the magazine indexing issue.
Features:
Compatible up to .30 caliber
Made by CNC for accuracy
Material is 6061 T6 Aluminum
Black anodize
Diamond pattern knurling for easy grip
DonnyFL
Hatsan Bullmaster | Invader | Galatian 1/2 x 20 Moderator Adapter #A35
$39.99
#A35 Adapter
1/2 x 20 UNF adapter for those rapid firing Bullmaster. New and improve design to allow more air flow.
Please note that when you add a suppressor to this gun, it does not properly index the magazine. It uses blowback air to advance the magazine however with a suppressor on, it over rotates and causes it to not properly index. If you plan to single load it'll work fine. Some customers have been able to get the gun to work properly by swapping out the spring inside the shroud with a different strength one. Will take trial an error.
Similar to the Blitz, this guy may need a lighter spring to work with a suppressor. I got mine from Ace hardware. See picture
Features:
Compatible up to .30 caliber
Made by CNC for accuracy
Material is 6061 T6 Aluminum
Black anodize
Diamond pattern knurling for easy grip
DonnyFL
Hatsan Jet 1 & Jet 2 Adapter | A111
$39.99
Features:
Any gun that needs a double-sided male adapter
Has through holes in the threads for easy tightening or loosening
Matte Black Anodize threads
.655 inches / 16.6 mm OD
DonnyFL
Hatsan QE Moderator Adapter A24
$44.99
Adapters are threaded for attaching a moderator
Thread: 1/2 x 20 UNF
Please note: I highly suggest getting a suppressor one size up from what your gun is. For example if you have a .25, get a .30. If you have a .30, the .30 cal suppressor is fine. This is to minimize the chance of the gun clipping.
Also if you have a Hatsan Bully .25/.30, based on customer's feedback I would go with the Emperor.
*We have not had any success with customers using a suppressor on Hatsan's line up of semi auto guns. It causes the gun to not index properly.
Features:
Matte black Anodized
CNC
Includes knurled thread protector
Compatible up to .30
Compatible with the following guns:
Hatsan GladiusHatsan Flash Wood QEHatsan AirMaxHatsan Bullboss QEHatsan BT65 QEHatsan Nova QEHatsan AT44-10 QEHatsan Hercules QEHatsan Flashpup QEHatsan AT P1Hatsan Flash QE
DonnyFL
Huben GK1 Pistol Adapter | A116
$34.99
Product description
This adapter allows you to add a 1/2 x 20 moderator or muzzle brake to your Huben GK1 Pistol.
Features:
6061 T6 Aluminum
Black Anodize
Knurled thread protector
DonnyFL
JTS | Aircuda & Aircuda MAX Adapter | A115
$49.99
Product description
Elevate your shooting experience with the DonnyFL JTS Aircuda and Aircuda MAX Adapter. Expertly crafted to let you seamlessly attach a DonnyFL Moderator to your rifle, this adapter ensures you can shoot with enhanced precision and reduced noise.
Key Features:
Compatibility: Perfect fit for JTS Aircuda and Aircuda MAX rifles. Suitable for .22, .25, .30 caliber variants.
Premium Material: Made with high-grade 6061 aluminum, ensuring durability and a lightweight feel.
Because this adapter was made to fit both the Standard and Max versions of the AirCuda, and because of the variations between individual rifles, you may find that one or two threads remain exposed when you snug the adapter in place. This is normal, and will not effect the performance of the rifle. In fact, our testing has revealed that a longer or heavier moderator can be used with less risk of clipping as compared to the endcap-only style adapter. It was necessary to design in this flexibility to overcome the challenges of this airgun's shroud design so that moderators can be used.
DonnyFL
Muzzle Brake Air Stripper Insert Kit #M58
$25.00
Upgrade kit for your fatboy muzzle brake. Comes with two air strippers for each size.
Note* Not compatible with the gold limited edition muzzle brakes.
Features:
.177/22, .22/25 and .25/30
Bronze anodize
Delrin tool to install air strippers
DonnyFL
Sam Yang .50 cal Dragon Claw A47
$50.00
Product description
Sam Yangs are known to output some crazy power. This adapter with M18x1 threads will allow you to screw on the Emperor v3. You might have need the Extender as well if Silence is a Priority!